GUIDE

How to set up geofenced clock-in

By the end of this guide, each of your workplaces in HourSquare will have a pin, a circle and a rule that decides what happens when someone clocks in from outside it. You will also know how to add an on-site code where presence matters most, and how to read the results in the first week.

Geofencing is a virtual boundary around a real place. In HourSquare it is called Clock-in location, and it is part of time tracking for every company. You can change it if you may edit workplaces. For the background, see the glossary entries on geofencing, buddy punching and time clocks, and the time tracking feature page.

Step 1: Decide the rule for each workplace

Every workplace has one of three rules. Off is the default for every workplace, so nothing changes until you turn it on.

  • Off: people clock in from anywhere, as before
  • Record: people clock in from anywhere, and each entry shows whether they were at the workplace
  • Require: people can clock in only inside the circle

Start with Record. It shows you how the readings look at each place without stopping anyone from clocking in. Move to Require once the results look right. A remote workplace has no pin, so there is nothing to set there.

Step 2: Open the setting

Go to Settings, then Workplaces. Select the workplace's entry in the "Clock-in location" column of the table, or open the workplace's edit form. When you add a new workplace, Clock-in location is offered as the suggested next step.

Step 3: Place the pin and choose the circle size

Put the pin where the workplace is. There are four ways to do it:

  • Select "Find this address" to look up the workplace's address on the map
  • Select "Use my current location" if you are standing at the workplace
  • Drag the pin on the map
  • Type the latitude and longitude

Then set the size of the circle, from 50 to 5,000 metres. The default is 150 metres, and it is a good place to start. Indoor readings can be rough, and a circle that is too small can lock out people who are standing inside the building, so start generous and make it smaller later if you need to. HourSquare already gives the benefit of the doubt: a person counts as inside when the distance minus the reading's accuracy is within the circle. A reading less accurate than 500 metres counts as location unknown.

Step 4: Tell your people before you turn it on

Explain what is checked and why before the rule goes live. Once it is on, people will see two things:

  • The first time they clock in, their browser asks for permission to use their location
  • A line under the clock says that their location is checked when they clock in

It helps to tell them what is kept, too. The Hub reads the location once at clock-in and once at clock-out, with no tracking in between. The server keeps the distance to the workplace, rounded to 10 metres, the reading's accuracy and the result. The position itself is not kept, and it is not written to logs.

Step 5 (optional): Add the on-site code

A determined person can fake a browser's location. Where presence matters most, add a code that can only be read at the workplace. Any device with a browser will do: a tablet, a monitor or a spare phone. Nobody signs in on it, and there is no hardware to buy and no app to install.

  1. In the workplace's Clock-in location settings, switch on "Ask for the code shown on a screen at this workplace"
  2. On the device at the workplace, open hub.hoursquare.com/screen. It shows a short linking code and a QR code
  3. Back in the workplace's settings, under "Add a screen", type the linking code and give the screen a name, or scan the QR code
  4. The screen now shows a six-digit code that changes every 30 seconds. People type it when they clock in

The device remembers that it is linked, so if the browser is closed and the page opened again, the code comes back. A workplace can have several screens, and the settings show the state of each one, for example "On · seen a minute ago" or "Never opened", with Rename and Remove. If no screen at the workplace has answered for 10 minutes, people are not asked for the code, so a dead tablet does not lock anyone out, and the entry is marked "Code screen was off". Five wrong codes in ten minutes pause that person's tries for a while.

Step 6: Check the first week

Open Time & attendance, then Today. Each entry carries a chip: "At workplace", "Away" with the distance, or "Location not shared". A count of flagged entries and a "Flagged locations" filter show the entries worth a look. Marks such as "New device" or "Code screen was off" never refuse anyone; they only flag. The same chips appear on timesheets and in approvals, and the attendance report and the time-entry export include the location result, the distance and the marks.

If most entries at a workplace show "At workplace" and the away ones have a reason you recognise, switch that workplace from Record to Require. If people you know were inside the building show as away, make the circle larger first.

What it will not do

  • It cannot stop a determined person from faking a browser's location. The on-site code is the stronger check, and the two can be used together
  • It does not check hours typed by hand. To close that, set Time recording to "Clock only"
  • It does not check clock-ins sent by a hardware time clock through the company API key, breaks, remote workplaces, or people with no workplace
  • It never refuses a clock-out, under any rule
  • It does not follow anyone between clock-in and clock-out
  • It works in the Hub, in a browser on a phone or a computer

Frequently asked questions

What if someone works from home some days?
Under Require, a clock-in from home is refused, because it is outside the circle. If people at a workplace often work from home, use Record for that workplace: they can clock in from anywhere, and the home days show as away with the distance, which a manager will recognise. A remote workplace has no pin and is never checked.
What happens at clock-out?
The location is read again and shown on the entry, but clock-out is never refused, under any rule. Someone who has already left the circle can always finish their day.
What if the tablet showing the code is off?
If no screen at the workplace has answered for 10 minutes, people are not asked for the code, so nobody is locked out. Their entries are marked "Code screen was off", and the settings show when each screen was last seen.
Can geofenced clock-in be faked?
A determined person can fake a browser's location. That is why the on-site code exists: it is shown only at the workplace and changes every 30 seconds. Using both gives the strongest check.
What does someone see if their clock-in is refused?
Under Require, a clock-in from outside the circle is refused with the distance, for example "You're about 2.3 km from Main Office. Clocking in works within 150 m of it." A clock-in with no usable location is refused too.
Who can change these settings?
Anyone who may edit workplaces in your company. Every change to the rule, the pin, the circle and the code switch is recorded in the audit log.

One e-mail a month

New templates, labor-law changes and what we shipped.

Ready when you are

Run HR yourself with HourSquare.

Sign up yourself, no demo needed. Free forever for teams of up to 10 people, and free for now for larger teams.

Free forever up to 10 people · GDPR-native · EU-hosted

HOURSQUARE · EST 2026 HR you run yourself.